|
RTI RHS780 Digital A/C
Refrigerant Handling System
Features
- Recover, recycle, and recharge service times average less than 10 minutes. The quickest in the industry!
- Patented recovery/recycling process - Heavy-duty compressor with true single-pass technology system
for maximum throughput.
- Digital heated power charge - Programmable with internal heating element.
A/C service equipment
refills most vehicles in less than 30 seconds.
- Advanced microprocessor - A/C service equipment
allows you to program charge amount, vacuum time, leak test, etc. and walk away.
- Pressure detection device - A/C service equipment
automatically restarts compressor if residual refrigerant is detected.
- Internal weight scale - Industrial-strength scale with shock absorber eliminates inaccuracies and
frequent calibration issues.
- Refrigerant inventory - Accurate, continuous tracking of recovered, recharged, and available refrigerant.
Long term memory for cumulative refrigerant management.
- Solenoid-controlled gauge manifold - No leaky panel valves to open and close.
Solenoids automatically open high and/or low side, eliminating potential mistakes.
- Pressure protection - Suction pressure regulator protects compressor and other critical components.
Specifications
- Electrical: 120VAC 60Hz. (230V available)
- Dimensions: 43"H x 24.5"W x 29"D
- Weight: 255 lbs.
- Operating Range: 32° to 122°F
- Scale Accuracy: ±0.03% load cell accuracy over useable range
- Hoses: 11 ft.
- Compressor: 1/3 HP, pressure protected, balanced startup
- Condenser: 2270 sq. in. - fin surface area 0.38" diameter copper tubing
- Condenser Fan: 5 blade, 8" diameter, 1550 RPM
- Vacuum Pump: 7 CFM, 29.9 In. Hg.
- Charging Cylinder: 30 lbs. DOT
- Cylinder Heater: Heat Belt, 200 Watt
- Process Time: Less than 10 min. average, recover/recycle/recharge
- Warranty 5 years parts, 2 years labor
|
RTI RHS730 Digital A/C
Refrigerant Handling System
Features
- Automation: Fully automatic service with pressure detection device
A/C service equipment automatically restarts compressor if residual refrigerant is detected. Microprocessor control allows
the technician to program vacuum time, leak test, charge amount, etc.
- Accuracy: Internal industrial-strength weight scale with shock absorber
A/C service equipment eliminates inaccuracies and frequent calibration issues. Refrigerant inventory continuously tracks recovered,
recharged, and available refrigerant for productive refrigerant management.
- Speed: Recovery/recycling process with heavy-duty compressor A/C service equipment
allows maximum throughput and service times of less than 12 minutes average. Large fan-cooled condenser allows speedy
recovery in high temperatures when A/C service is in demand.
- Reliability: Highest quality compressor, solenoids, circuit board, switches, wiring, filters, weight scale, etc.
Pressure regulator protects compressor and other critical components.
- Intuition: Digital readout using plain language information and technician prompts makes this service
so easy that any technician can be an AC expert. Solenoids automatically open high and/or low side,
eliminating potential mistakes.
Specifications
- Refrigerants: 2 models available: R134a or R12
- Electrical: 120VAC 60Hz. (230V available)
- Dimensions: 49"H x 20"W x 20"D
- Weight: 244 lbs.
- Operating Range: 32° to 122°F
- Scale Accuracy: ±0.03% load cell accuracy over useable range
- Hoses: 11 ft.
- Compressor: 3/8 HP, pressure protected; oiled, hermetic
- Condenser: 2270 sq. in. - fin surface area 0.38" diameter copper tubing
- Condenser Fan: 5 blade, 8" diameter, 1550 RPM
- Vacuum Pump: 7 CFM, 29.9 In. Hg.
- Charging Cylinder: 30 lbs. DOT
- Cylinder Heater: Heat Belt, 200 Watt, thermostatically controlled
- Process Time: Less than 12 min. average, recover/recycle/recharge
- Warranty 2 years parts and labor
|
RTI RHS980 Dual Digital A/C
Refrigerant Handling System
Features
- Control panel mounted on a revolving turret—the
turret rotates 90 degrees in either direction for
unrestricted viewing capability—this eliminates
machine repositioning for the technician.
- Intuitively easy-to-use function input and display—
– Extra large character (4 x 20) LCD display.
– Intuitive plain language prompts.
– Language capability pre-programmed with
- English, Spanish, French, German. Other foreign
languages can be accommodated.
– EZ-Select menu-driven programming inputs.
– Conveniently reached keypad with tactile button
panel controls.
- Easy-to-read large face, High and Low pressure
gauges.
- Ergonomic mobility handle – perfect for hose storage
and low-effort machine positioning.
- Low rolling resistance, cushioned, non-inflatable rear
wheel/tire assemblies—no-maintenance, provides
easy machine handling
Specifications
- Electrical: 120VAC - 60HZ - 12 AMP 230VAC - 50HZ - 6 AMP (Optional)
- Shipping Dimensions: 50 in x 22 in x 35 in (127 cm x 56 cm x 89 cm) (H x W x D)
- Weight Approximately: 255 lbs (116 kg)
- Operating Ranges: 32Deg. - 120Deg.F (0Deg.-49Deg.C)
- Scale Accuracy: J2788 Compliant
- Recovery Accuracy: J2788 Compliant
- Hoses: 9 ft (2.74 m)
- Compressor: 3/8HP – 0.8kW, pressure protected, balanced start-up, oiled, hermetically sealed
- Condenser Fan: Industrial-duty
- Vacuum Pump: 7 CFM, dual stage, 29.9 InHg
- Charging Cylinder: 30 lb (13.6 kg) DOT
- Recycling Filter-Drier Spin-on type:
- Mfg Warranty: 2 Years
 VIEW BROCURE
|
Robinair 34134Z A/C Dual Refrigerant
Management Center
Features
- Field Proven Compressor -Quickly pulls refrigerant from the system
during recovery to save time; also pulls the system into a vacuum prior to
recharging.
- Electronic Scale -Makes it simple to recharge to factory specifications; also weighs recovered refrigerant and provides tank overfill protection.
- Microprocessor-Signals when it’s time to change the filter-drier and drain the system oil.
- High Capacity Filter-Drier -Removes contaminants during single pass recycling; replace the entire canister for fast changeovers.
- Manual Air Purge -Removes air from the refillable tank, the gauge on the control panel shows when to purge air.
- Two-Way Manifold -Detachable so it can be used away from the unit or hung on the vehicle so it’s easy to monitor pressures during service; controls the flow of refrigerant.
- Toggle Switch -Selects either pounds or kilograms.
Specifications
- Voltage 115V 60Hz
- Refrigerant Container 30 lbs. (14 kg) refillable, D.O.T. approved (included)
- Operating Range 50 degrees to 120 degrees F (11 degrees to 49 degrees C)
- Recovery Rate ½ lb. Min. (.2kg/min.)
- Recycling Filter Drier 43 cu in (710cc) Spin-on
- Shipping Weight 65 lbs. (30kg) without tank
- Dimensions 45”H x 22” W x 28”D 114 cm x 56cm x 71cm)
|
Robinair 34288
Dual Refrigerant Recovering/Recycling
The Cool-Tech 34288 combines simple operation with superior accuracy. It recovers, recycles, evacuates, leak tests, and recharges R-134A quickly and accurately. Meets SAE J-2788 standards for accuracy: 95% refrigerant recovery and charging to +/- 1/2 oz.
Features
- Automatic Air Purge
- Refrigerant Charging
- Refrigerant Management
- Vacuum Function
- New 4x20 multilingual display
|
Robinair 34788
R-134a Recovering/Recycling
The Cool-Tech 34788 combines simple operation with superior accuracy. It recovers, recycles, evacuates, leak tests, and recharges R-134a quickly and accurately. Fully automatic function lets you recover, vacuum, leak test, charge, and then walk away. Other features and functions:
- Vacuum Leak Test
- Automatic Refrigerant Refill
- Automatic Air Purge
- Automatic Oil Drain
- Refrigerant Charging
- Refrigerant Management
- Vacuum Function
Features
- Recovers 20% More Refrigerant
- Charge Accuracy +/- 1/2 Ounce
- Control panel offers flat storage feature when not in use
- Database expansion slot
- Two large tool storage areas
- Change between traditional & hybrid vehicle systems without fear of cross contamination with improved oil injection
- New 2X larger display makes the 34788 easier than ever to use
- Built-in storage for extra filter
- On-board storage for compressor oils
With Automated A/C Service
|
Robinair 75700
CoolTech Coolant Exchanger
Features
- Our 10 minute exchange process means no more waiting for the engine to warm up!
- Our “engine Off” feature removes pulleys, belts, and fan blades from the safety equation.
- Vacuum mode creates a “push/pull” exchange process allowing the technician to safely remove high pressure in a hot system.
- Leak check feature allows the technician to test for leaks prior to refilling.
- Two clearly marked valves and an easy-to-read gauge make this machine very easy to use.
- No electricity required. 90 psi shop air drives the exchange process, as well as the 2 gpm pump on the waste tank.
- Two external new coolant supply tanks allow on-board storage of two different coolant types
Specifications
- Power Supply – 90 psi shop air
- Tanks
– Internal waste – 15 gallon capacity
– External supply (2) 5 gallon capacity (removable)
- Dimensions: 47" H x 26" W x 33" D (119 cm x 66 cm x 84 cm)
- Medium Step Adapter, Two included; fits hose size 1-1/4", 1-3/8" and 1-1/2"
- Large Step Adapter, Two included; fits hose size 1-3/4", 2", and 2-1/4"
|
|
Note: The features and specifications listed above are provided by the
manufacturer(s) and may change without notice.
Call Vehicle Service Equipment for Information. |
.gif){kind=logo}